Interior Restore Part 2

Well today I finished all of the upholstery work. I still need to do the door panel leather but the seats are done. Tomorrow I’ll begin work on the radio install as well as the new dash cover.

Pics of the leather seats are below:

The center console was the worst of the bunch. We had to snap off retaining trim to get access to the old cloth which was tacked down by stables. After ripping that off we were able to put the new leather on. In this pic you can see the new leather as it was stapled down.

Broader view.

This is the piece after it was done. It’s basically the cap on the center console compartment.

This is the pneumatic stapler we used to tack the leather. $25 at Harbor Freight!

Another shot.

Tacking the retaining trim back down over the new covering.

After cutting the leather to fit around the hatch release button.

We’re putting the leather cover of the bottom half of the center console. There wasn’t much leather to work with here so it was pretty tight. My hands are still sore.

Stapled down.

And now the retaining trim has been snapped down.

Getting there.

Finished product all put back together. NOT BAD!

And finally the drivers chair. These are the internals of the chair to give you an idea of how all the electronic comfort options work.

This chair was very similar to the passenger side from the last update so it was pretty easy at this point. I can’t wait to see them in the truck.

Tomorrow I begin work on the new audio system. Stay tuned for an update.

2001 Dodge Ram Interior Restoration

I’ve had this truck for a long time and after many camping trips with Les and the kids the interior has become a little worse for wear. This year I bought some new leather upholstery from LeatherSeats.com. I also picked up a new carpet from StockInteriors.com. I chose a two tone leather and a mist gray carpet.

The first step was to remove the seats and carpet.

After the seats were unbolted and removed the carpet looked terrible! Wow a lot of crud fell under the seats.

The seats out and on the garage floor.

Justin helped remove the rear bench seat.

I guess Justin thought it was hard work.

After the carpet was removed this is what was left.

So now that everything is out my plan is to replace the carpet, recover the seats, upgrade the audio system (better sounding, blue tooth, dvd for rear passengers, and a rear view camera), and finally put a dash cover on the dash to cover the cracked dash. Today we began working on the seat covers.

This is the rear bench seat and where the 3 boys spend most of their travel time on camping trips; so it’s a big friggin mess. I put it up on saw horses and began to take it apart.

After taking the plastic covers off I could see the seat release mechanism. This is what holds the seats together and controls the up/down motion of the bottom seat for under seat storage. Before I could get the seat back off I needed to remove this by removing the 2 bolts. This allowed the seat back to come free.

Starting with the bottom cushion, I removed the old seat cover by peeling it off.

Putting on the new cover was as simple as flipping it inside out and rolling it onto the cushion. Very easy! Leatherseats.com puts a zipper on the back side of the cover to seal it up.

After a very similar process, the seat back was covered. We put it all back together and here is the finished product.

Next, the passenger seat.

We turned the seat upside down and found 4 bolts used to hold the bottom cushion in place. After removing these the cushion was easily removed from the chair.

This is a hog-ring. Apparently they are used quite often in upholstery. I found some hog ring pliers and some hog rings at Ace Hardware so that I could tack down the new cover.

The bottom cushion with the new cover.

Now the seat back. This was pretty easy except for the seat belt slot located in the seat back.

I cut a slot in the leather and trimmed enough foam and leather to allow the bracket to click back into place.

The final product.

Next the center console. We didn’t finish it today but holy crap what pain in the a$$. More to come later!

MBRP Exhaust for My Wife’s 2005 Dodge Ram

Last week my wife complained about a new and annoying rattle underneath the truck as she was driving the kids to school. That weekend I crawled underneath the truck and discovered that the exhaust was about to fall apart! The previous owner had removed the muffler and straight piped it. To connect everythign together they welded the joints, which is where it all began to break apart.

To hold over the busted exhaust I got some flashing and some hose clamps. This kept the weld from breaking completely.

Before we kicked off this project I took some video of the current exhaust. I wanted to have documented proof of the sound improvement.

We always hated this sound. It was very hollow and at highway speeds it would drone and drone and drone.

The first step was to break the connection between the catalytic converter and the old broken exhaust. I was a little worried about this because of the type of clamp used and the rust.

To get easier access to everything I cut the pipe. Then…

I cut it again. This provided some wiggle room needed to pry the hanger bushings off of their support to remove the exhaust from the truck.

Old exhaust on the floor.

To remove the piece of pipe that was attached to the cat I needed to cut it a little. I used a grinding wheel and cut a 2 inch incision into the pipe. With that taken care of I was able to get a screw driver in there and break the hold. A few bangs with a hammer and the pipe came off.

This is the small pipe that was on the cat. You can see the cut I made to remove it.

Old exhaust next to new. Notice the new muffler. Yay!

The MBRP kit comes with an extension pipe sized for a 8ft bed + a quad cab truck. This truck is a short bed quad cab so that means I needed to cut the pipe. This pic is of the pipe on the vice waiting for the reciprocating saw. The pipe needed to be cut to 10.5 inches plus the flange.

The freshly cut pipe and muffler connected.

From the muffler to the back of the truck.

Now the clamps go on.

More clamps.

The connection to the catalytic converter.

The exhaust tip.

And finally the resulting sound!

The Wood Heater Has Been Installed

I admit it. I’m a procrastinator. Over the years I’ve tried and tried to kick the habit but I just can’t.

So, I FINALLY installed the wood heater … just in time for spring. Go figure, I guess I’ll warm the garage next year.

Check out the pics below to see the installation. It went well. I had to call in Tony to help out with the roof top stuff because I just can’t handle heights. We did have one cold day post install and I was able to raise the temp in the garage about 20 degrees so I guess it’s a success. I’ll report back next year when the ambient temp is around 35ish and we’ll see if it does the trick.

About the project: I got the wood heater from Bruce of Asheville (see previous post). I installed it on some brick adjacent to the auto lift. I figured that I would be working over there most of the time so that location made the mot sense. Plus, the distance to the ceiling was shorter there so I didn’t have to invest in as much stainless steel pipe. I ordered a industrial ceiling fan from Grainger to help keep the air in the garage moving – heat rises so the fan keeps it flowing. Stan, my father in law, did the wiring and installed the fan.

This fire is super hot. The stove has a really good draft and the blower works well.

This fan moves lots of air!

Justin is testing out new equipment.

New Wood Stove

Obviously, it gets pretty cold out in the garage during these winter months. To help take the chill off, I just bought a used wood stove from a really cool guy that lives out near Asheville. He was kind enough to deliver it to me during one of his trips to the area. Thanks Bruce!

I ordered all the pipe for the chimney and that should hopefully arrive this week. I also ordered an industrial ceiling fan from Grainger that will be used to circulate the warm air. Here are a couple pics of the stove.

PS, I wanted to take the time to plug a cool craigslist application called “Ad Notifier”. I used it to find the wood stove by entering key words into the software. After that it would pole craigslist every 5 minutes for new ads that matched the search criteria. Highly recommended!!

Ad Notifier Website

Matt Hazard: Blood Bath and Beyond Launches

I know this isn’t really a garage oriented update but I’m pretty excited about our latest video game offering and wanted to talk about it here.  Our latest game, Matt Hazard: Blood Bath and Beyond, launched yesterday on Xbox Live Arcade and today on PlayStation Network for the PS3.  It’s an old school, Contra style arcade shooter and it is HARD! If you’re up for a challenge then check it out!!

Our first review came through yesterday on IGN.  If any of you are unfamiliar with the games industry, IGN is basically one of the top two review publications on the internet.  They gave us a 7.9 out of a possible 10.  Even though I think it is much better than a 7.9, I am extremely happy about this.  Our games tend to not get the hype and attention that other blockbuster games get which often translates into poor reviews.  Also, I believe this game ended up being nicely scoped for the time we had to build it.  I am hopeful that we get similar or better treatment in the GameSpot review. 

Anyway, check out the media below for an idea of what BBB is all about.  Warning: the game is rated M so there is some blood in the footage.